What is the Proper Method of Drop Ceiling Installation Drop Ceiling Lighting

What is the Proper Method of Drop Ceiling Installation?

Generally, to give a final touch to the basement, drop ceiling installation needs to be done. Drop ceiling would make your home look good. Also known as the suspending ceiling, drop ceiling would need drop ceiling tiles to be built. You would need a system of tracks in order to install it, rather than working on an overhead drywall. Sometimes, a drop ceiling might be required to install for a different purpose rather than giving a final touch to the basement. This article discusses the complete method on how to install a drop ceiling so that you can efficiently and very quickly install the drop ceiling whenever required.

Materials Required

You would need to collect the materials required for the Drop Ceiling Installation in advance so that problems are not faced afterwards. Following things need to be collected:

•    Level – you can either use a standard level or a laser level

•    A hammer or a staple gun

•    Nails or staples based on what you have chosen among hammer of a staple gun

•    A few tin snips

•    A chalk to do the markings, pencil can also help

•    A few eye bolts

•    A suspension wire

An Important Tip

Make sure that you check the municipality codes and the local building codes as well before continuing with the drop ceiling installation. In some of the areas, there is a fixed limit on what height the drop ceiling can be. For example, in the United States, the drop ceiling must be at least 2.3 m high from the floor. Also, make sure that you wear safety goggles while performing all the steps listed as under. In case you need to install the drop ceiling lights as well, it would be advisable to make the arrangements beforehand so that you need not repeat the steps afterwards.

Mark Location for Ceiling Brackets

This is the basic step of the drop ceiling installation. You would need to mark the location of the brackets in which ceiling has to be installed. Most of the time, a 3 to 4 inch from joist ceiling is preferred so that some space if left in which the tiles can be maneuvered. However, in case you would be installing drop ceiling lights as well, make sure that the ceiling you are installing is at least 6 to 7 inches from joists. No matter you are using a standard level for this purpose or you are using a laser level, the results would be same, however, if you want ease of operation a laser level would be preferable. Most of the time, people make the mistake of assuming the original ceiling to be the level, you must not make this mistake and use a level instead.

Mount the Bracket

Remember, a perimeter bracket is the only part of the drop ceiling which is in direct contact with the wall. So, you need to work them right, as the entire drop ceiling might be supported by them. You can take the molding and then measure the length that you need. The rest of the molding can be trimmed easily with the help of tin snips. You can also use some other tools if you desire. After trimming, the molding or the brackets would need to be installed on the wall with either staples or nails. As soon as you reach the corner, you would need to align the moldings, so be very careful about it.

Determine the Tiles Count

A specific number of tiles would be required to cover the ceiling. So, there is no wisdom is buying lesser or the extra number of tiles. Just a little mathematics, and you would get the number. Measure the distance between the moldings using a measuring tape and then divide it with the width of the tiles that you plan to use. This was for the general case. In case you need designer tiles with different tiles for the border and different ones for the center, you would need to apply more calculation. However, make sure that your tiles are not less than 6 inches in width even after trimming.

What is the Proper Method of Drop Ceiling Installation Drop Ceiling Lighting

Make Way for the Runners

Runners are actually supporters which would support the drop ceiling tiles over the ceiling. So, you would first need to install the runners and then install the tiles. Choosing the location of the runners can be daunting, but if you install the first runner in the correct position, the task would become easy afterwards. You can use a chalk to mark the points where runners need to be installed. Make sure that all the runners are at least 4 feet apart. And, make the markings across the entire ceiling.

Install the Runners

Now, this is the time to install the runners. You can use eye bolts for their installation. Grab some pieces of wires and then suspend the runners with the joists. Before tightening them, make sure that they are levelled properly and you can use taut string run. Trimming might be required in some of the cases, be sure about whether your runners need it or not. Install the runners all over the ceiling of the room wherever you have marked the points for their installation.

Install the Cross Tees

The cross tees would be needed to complete the entire grid. You would need to calculate the number of tees required in advance. There is no general rule for this calculation and would generally depend on what size of tiles you have used for your drop ceiling.

Install the Ceiling Tiles

This is the final step where you have to install the ceiling tiles. Hold a tile in tilted position and then just slide it into the place meant for its installation. When it is properly fitted, you can leave it and then continue repeating this process till all the tiles get installed.

Congratulations! You have successfully installed the drop ceiling in your home.

Leave a Reply