Hang Crown Molding Without a Nail Gun

Hang Crown Molding Without a Nail Gun

Install Crown Molding Without a Nailgun

Were finishing up a big dining room renovation, and I cant wait to show you everything because I LOVE it!

One thing I have always wanted in my house was crown molding. I think it finishes a room and makes it look so much nicer! I thought it would be really expensive or difficult to install, or need a ton of fancy tools, but it isnt.

With some patience, a few basic skills, and a few tools you probably already have, you can install crown molding yourself- without a fancy nailgun- and make it look professional- in a few hours!

This way does require a few extra steps (a nail gun would eliminate all the work I am detailing below, minus the caulking, but we couldnt get our hands on one, and the work around is actually REALLY EASY. I promise!).

First off, you need to measure your space, and buy molding. I went for unpainted (whats up major savings I can paint myself for $5 less a yard!), and bought twice the amount I thought I needed. Which was super helpful unless you want a zillion seams, because mess-ups happen. Both Home Depot and Lowes have a fabulous selection of crown molding- both painted and unpainted.

First, I painted the trim with some killz to prime it. I then painted it with Clark & Kensingtons Antique White from Ace Hardware- that PERFECTLY matches our houses white- and since we need to repair our dining room ceiling anyways (meaning repainting), I went for the same color on the trim so it can all be done at once.

I am into lazy solutions like that.

My dad then cut the molding for me since I am a tad awful at measuring. He cut at an angle on our mitre saw- if you dont have one, you could ask the hardware store to pre-cut for you if you know your walls measurements.

www.youtube.com/watch?v=vPJCXTM810U. We did have one seam in between strips of molding per wall. The seams blend in perfectly after you caulk and paint over them, so dont worry if you cant find a single strip of molding long enough.

My dad actually measured, cut, measured, cut, and measured each strip again. Each piece took him about 3-4 cuts to get it exactly perfect- but it is much better to cut a few times to get it right than to overcut. Take your time and measure carefully when cutting your molding, or you will have a ton of seams and four letter words!

Start off by finding studs in your walls. Then hold up the molding on your walls where you would like it to go and drill a hole through them into the studs. We were lucky that our walls had a stud running along the top of the wall, so we didnt have to worry too much about using the studfinder the whole time (what an awesome discovery THAT was!!).

Next, using long finishing nails, nail your trim in place (lined up with the holes you previously drilled). It is crucial to have someone hold the trim in place for you and keep it taut with the wall- especially if you have uneven ceilings (or walls) like I do so it is flush against them. You dont want any gaping bits (if we didnt watch, the molding would easily have been crooked. A lot of new construction houses have uneven ceilings!)

Dont nail all the way in- just into the stud enough so the trim can hang, unsupported. You dont want to come too close with your hammer or you could smash, nick r ding your beautiful molding!

Youll grab your finishing tool next (they are like under $5 at hardware stores- be sure to grab one with a tip that is larger than your nail heads, or it will be harder to control. Hold the finishing tool in one hand, and line it up with your nail. With your other hand, hammer the end of the finishing tool to drive your nail into the trim- nick free.

Using spackling compound or wood putty, smooth over the nails  completely.

Caulk along the top and bottom of the molding. If you dont want to repaint the wall or ceiling, tape off the area you dont want caulked. Youll notice we only taped off under the molding since we have massive gaping holes in our ceiling and are going to have to repaint it all anyways when that gets fixed.

Let the spackle/wood putty and molding dry, and remove tape.

When the putty is totally dry, usually overnight, use a fine sanding block or piece of sanding paper, go over the putty and make it completely smooth with the molding.

How easy was that? It might seem like a few steps, but it really isnt much work once you have the molding cut. Where would you most like to add crown molding?


Leave a Reply