Controlling Floor and Ceiling Heights Chief Architect Knowledge Base

Controlling Floor and Ceiling Heights Chief Architect Knowledge Base

Controlling Floor and Ceiling Heights

QUESTION

What is the best way to set floor and ceiling heights in my split level, or multilevel plan?

ANSWER

There are a few basic concepts to bear in mind when setting floor and ceiling heights in a plan, especially when creating a split level type design.

  • You can set the ceiling height for an entire floor in the Room Defaults dialog, then make any necessary changes on a room-by-room basis.
  • Floor and ceiling heights can be altered at any time; but it’s best to wait until you have created all the floors in your plan before changing individual rooms.
  • You should finalize all floor and ceiling heights before building the roof.
  • To specify a default ceiling height

    1. Select File New Plan from the menu to open a new, blank plan.
  • Select Edit Default Settings from the menu, and in the Default Settings dialog, select Floor and click the Edit button.
  • In theFloor 1 Defaults dialog, select the structure panel, and specify the desired value for Finished Ceiling (F) for the rooms on the first floor.
    • Specify the height of the tallest ceilings on this floor, but ignore the ceiling heights of any rooms that will extend into the floor above, such as a vaulted entry area.
  • For example, if your living room, dining room and kitchen will have 9′ ceilings while a powder room and hallway will be only 8′ high and the entry, 18′ high, specify the default Finished Ceiling (F) as 9′ (108″).

    Again, recall that in version 9.0 and prior programs, you will adjust the Ceiling Height (B) value in the Structure Tab.

  • Click OK to apply these changes and close the dialog, then click Done to close the Default Settings dialog.

    Now that we have set up our defaults, we are ready to begin drawing our basic plan.

    To draw the basic plan

    1. Select Build Wall Straight Exterior Wall from the menu and draw four walls to enclose a single rectangular room.

    In this example, a 20′ x 30′ rectangle is drawn.

  • Click the Select Objects button, then click in the room within these walls to select it.
  • Click the Open Object edit button to open the Room Specification dialog and on the Structure panel, notice that the default ceiling height that you specified is used. Click Cancel to close the dialog.
  • Select 3D Create Camera View Doll House View to see the current floor in 3D.

    To raise a single room’s ceiling height

    While it is not recommended that you change a room’s ceiling height when additional floors have yet to be created, we will do so in this example to illustrate how this change will affect the model.

    1. Close the 3D view to return to floor plan view, then select Build Wall Straight Interior Wall. and click and drag two walls to create three separate rooms.
  • Click the Select Objects button, then click in one of the rooms to select it.

  • Click the Open Object edit button to open the Room Specification dialog.
  • On the structure panel, increase the Finished Ceiling (F) value. For the purposes of our example, we will raise it to 11′ (132″).
  • Select 3D Create Camera View Doll House View to see the results.

    To lower a single room’s ceiling height

    Again, we are changing ceiling heights now only to illustrate the effect on the model.

    1. While still in the Doll House View, click the Select Objects button, then click in a different room to select it.
  • Click the Open Object edit button to open the Room Specification dialog. On the Structure panel, decrease the Finished Ceiling (F) value and click OK. For the purposes of our example, we will set it to 7′ (84″).
  • In a Doll House View. you can see how this change affects the walls.

    To create a new floor

    1. Close the 3D view to return to floor plan view and select Build Floor Build New Floor from the menu.
  • In the New Floor dialog, select Derive 2nd Floor from 1st Floor plan and click OK.

    A new floor is created with exterior walls directly above those on the floor below.

  • Go Down One Floor and create a Doll House View. Notice that the program has restored the default ceiling height to the rooms on this floor.
  • Close the 3D view to return to floor plan view, then go Up One Floor to the new Floor 2.
  • Just as on Floor 1, select Edit Default Settings from the menu and open the Floor Defaults dialog for Floor 2.
    • Specify the desired default Finished Ceiling (F) for Floor 2, then click OK.

    Note: If you specify a different Floor Height. the default Ceiling Height of the floor below will be affected.

    To create a stepped ­floor platform

    When all of your floors are in place with the correct default heights, you can make changes to individual rooms. In this example, we will raise the floor of a room on Floor 2 and increase the ceiling height of the room below as a result.

    1. Select Tools Reference Floors Reference Display from the menu to turn on the Reference Display, which allows you to see the position of objects on the floor below by displaying them in red.
  • Select Build Railing and Deck Straight Railing from the menu, then click and drag a railing over one of the interior walls on Floor 1.
  • Click the Select Objects button, then click on the railing to select it and click the Open Object edit button.
  • On the General panel of the Wall Specification dialog, check the box beside Invisible and click OK.
  • If an option to Align with Wall Below is available on the edit toolbar, click on it to align the walls.
  • Click in the small room created by the railing and click the Open Object edit button.
  • On the General panel of the Room Specification dialog, increase the value of Floor Height and click OK.
  • You can see the results by selecting 3D Create Camera View Camera from the menu and clicking and dragging a camera arrow in the larger room, towards the railing.
  • If you return to floor plan view and go Down One Floor. you can open the Room Specification dialog for the room directly below the one with the raised floor and see that its Finished Ceiling Height has been adjusted upward.


  • Leave a Reply